Mod for Tri-pod 2" legs
- planecrazzzy
- Articles: 0
- Posts: 192
- Joined: Wed Jul 27, 2022 1:14 am
- 1
- Location: Above 47 Minne-snow-ta
- Status:
Offline
Mod for Tri-pod 2" legs
.
OK, here's something easy to remember...
Pipe is measured from the INSIDE...
Tubing is measured from the OUTSIDE...
.
The Legs are 2" tubing... ( This is O.D )
PVC plastic pipe is 2" ...( This is I.D. )
.
I've used this style of clamping several ways...
Most of them were PVC on PVC
Finding the right amount to cut out is easy to do...
If you don't open it enough...trim it some more.
If you trim it too much...Throw it away , these are cheap.
You can also vary the strength by how wide you cut your pipe ( see three examples, smallest was used )
.
Once you get a size you like...Save the piece cut out...
Cut your next piece... THEN mark it once for a close tolerance...
.
I notice these SLIDE freely after I slip one on the tube...
But with a wire or two under them , they stay in place...
.
For This application...
.
I'm going to want all wires going down one leg , These clips will hold several wires.
or just add more clips .
.
HEY... Is that Red Anodized Aluminum to match your Camera ?
Or a piece of plastic colored with a red Sharpie...(paint will chip from flexing)
.
Hope you like it...
.
Gotta Fly...
.
.
- Lady Fraktor
- Articles: 0
- Posts: 10074
- Joined: Mon Apr 29, 2019 9:14 pm
- 5
- Location: Slovakia
- Status:
Offline
Re: Mod for Tri-pod 2" legs
The only culture I have is from yogurt
- Gordon
- Site Admin
- Articles: 1051
- Posts: 8477
- Joined: Wed Apr 24, 2019 10:52 pm
- 5
- Location: Cottonwood, AZ
- Status:
Offline
-
TSS Awards Badges
TSS Photo of the Day
I Broke The Forum.
TSS EAA Messier awards
Re: Mod for Tri-pod 2" legs
Scopes: Explore Scientific ED80CF, Skywatcher 200 Quattro Imaging Newt, SeeStar S50 for EAA.
Mounts: Orion Atlas EQ-g mount & Skywatcher EQ5 Pro.
ZWO mini guider.
Image cameras: ZWO ASI1600 MM Cool, ZWO ASI533mc-Pro, ZWO ASI174mm-C (for use with my Quark chromosphere), ZWO ASI120MC
Filters: LRGB, Ha 7nm, O-III 7nm, S-II 7nm
Eyepieces: a few.
Primary software: Cartes du Ciel, N.I.N.A, StarTools V1.4.
- planecrazzzy
- Articles: 0
- Posts: 192
- Joined: Wed Jul 27, 2022 1:14 am
- 1
- Location: Above 47 Minne-snow-ta
- Status:
Offline
Re: Mod for Tri-pod 2" legs
I like them better Black... But I couldn't waste the opportunity to add some "Bling"
Since the red was already on the set of three that I'm using , I thought I'd put
some stick-on letters , Hmmm , nothing that size without going over to the shop.
So, I taped it off and with a little x-acto action...no blood was drawn.
JAM is what I use... Cause there are too many Mike's
Jam is "Just Another Mike"
.
My Dad had an Excavating Co call "Another Excavator"
So this sorta ties in with that.
.
Gotta Fly...
.
What I'm trying to do is give you an example of how YOU might do them...Stock White if yer scope is white ?
- planecrazzzy
- Articles: 0
- Posts: 192
- Joined: Wed Jul 27, 2022 1:14 am
- 1
- Location: Above 47 Minne-snow-ta
- Status:
Offline
Re: Mod for Tri-pod 2" legs
.
This shows how many cables these hold...
.
But , one set of this down the tri-pod leg , can be shared by another set...staggered clamps,
.
I've never seen any of the telescopes use more cables than this example. ( But I'm sure SOMEBODY does )
.
Gotta Fly...
.
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute